Thermodynamic integration with harmonic reference

The Helmholtz free energy ($A$) of a fully interacting system (1) can be expressed in terms of that of system harmonic in Cartesian coordinates (0,$\mathbf{x}$) as follows

$A_{1} = A_{0,\mathbf{x}} + \Delta A_{0,\mathbf{x}\rightarrow 1}$

where $\Delta A_{0,\mathbf{x}\rightarrow 1}$ is anharmonic free energy. The latter term can be determined by means of thermodynamic integration (TI)

$\Delta A_{0,\mathbf{x}\rightarrow 1} = \int_0^1 d\lambda \langle V_1 -V_{0,\mathbf{x}} \rangle_\lambda$

with $V_i$ being the potential energy of system $i$, $\lambda$ is a coupling constant and $\langle\cdots\rangle_\lambda$ is the NVT ensemble average of the system driven by the Hamiltonian

$\mathcal{H}_\lambda = \lambda \mathcal{H}_1 + (1-\lambda)\mathcal{H}_{0,\mathbf{x}}$

Free energy of harmonic reference system within the quasi-classical theory writes

$A_{0,\mathbf{x}} = A_\mathrm{el}(\mathbf{x}_0) - k_\mathrm{B} T \sum_{i = 1}^{N_\mathrm{vib}} \ln \frac{k_\mathrm{B} T}{\hbar \omega_i}$

with the electronic free energy $A_\mathrm{el}(\mathbf{x}_0)$ for the configuration corresponding to the potential energy minimum with the atomic position vector $\mathbf{x}_0$, the number of vibrational degrees of freedom $N_\mathrm{vib}$, and the angular frequency $\omega_i$ of vibrational mode $i$ obtained using the Hesse matrix $\underline{\mathbf{H}}^\mathbf{x}$. Finally, the harmonic potential energy is expressed as

$V_{0,\mathbf{x}}(\mathbf{x}) = V_{0,\mathbf{x}}(\mathbf{x}_0) + \frac{1}{2} (\mathbf{x} - \mathbf{x}_0)^T \underline{\mathbf{H}}^\mathbf{x} (\mathbf{x} - \mathbf{x}_0)$

Thus, a conventional TI calculation consists of the following steps:

1. determine $\mathbf{x}_0$ and $V_{0,\mathbf{x}}(\mathbf{x}_0)$ in structural relaxation
2. compute $\omega_i$ in vibrational analysis
3. use the data obtained in the point 2 to determine $\underline{\mathbf{H}}^\mathbf{x}$ that defines the harmonic forcefield
4. perform NVT MD simulations for several values of $\lambda \in \langle0,1\rangle$ and determine $\langle V_1 -V_{0,\mathbf{x}} \rangle$
5. integrate $\langle V_1 -V_{0,\mathbf{x}} \rangle$ over the $\lambda$ grid and compute $\Delta A_{0,\mathbf{x}\rightarrow 1}$

Unfortunately, there are several problems linked with such a straightforward approach. First, the systems with rotational and/or translational degrees of freedom cannot be treated in a straightforward manner because $V_{0,\mathbf{x}}(\mathbf{x})$ is not invariant under rotations and translations. Conventional TI is thus unsuitable for simulations of gas phase molecules or adsorbate-substrate systems. and this problem also imposes restrictions on the choice of thermostat used in NVT simulation (Langevin thermostat, for instance, does not conserve position of the center of mass and is therefore unsuitable for the use in conventional TI).